DYNOJET 4165.001 PDFDYNOJET 4165.001 PDF

1. Remove the vacuum slides from the carbs. Remove the stock needles and spacers, noting the order of assembly. This kit is labelled US Only (Serial No) I have been in contact with DynoJet and they assure me that mechanically this is identical to the European kit. Dyno Jet kit installed as per instructions and has mains. . I don’t know anything about the Ivan’s kit but Dynojet advise that to make changes to.

Author: Majinn Tull
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 6 November 2016
Pages: 251
PDF File Size: 1.61 Mb
ePub File Size: 4.28 Mb
ISBN: 731-6-90594-450-6
Downloads: 25046
Price: Free* [*Free Regsitration Required]
Uploader: Nizuru

Also when I close the throttle she drops to rpm and just stays there for about 30 seconds and then slowly returns to proper idle. Damaged or restricted fuel tank venting system. Its got a short afermarkt pipe on wich bckfired alot before but since ive change the jets its not backfiring anymore.

Please enter your desired user name, your email address and other required details in the form below. Last edited by biaggi; at In order to be able to post messages on the Yamaha R1 Forum: You can’t post conmments that contain an email address.

Valvetrain noise is usually the tensioner,or the guides loosening up a little. How can this be resolved. Tell us some more! Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.


Remove the stock needles and spacers, noting order of assembly Fig. Posted on Apr 14, Damaged float bowl o-ring. I don’t like the sound of your dealer.

Does the body make a charge 41665.001 Install the Dynojet needles on groove 3, using all stock spacers. Please assign your manual to a product: BB code is On. Box San Rafael, CA Particle contamination in inlet fitting cavity. The engine should be at operating temperature with the enrichener off to set the idle between rpm.

Documents et livres connexes

Document Checklist – Students Applying for a If he’s done a major service then setting up the carbs should be included Your plug does look rich or an electrical problem. Spray dynohet the connections with WD40 or similar. Use of a Representative IMM dyynojet, if applicable. If this application form is completed on a computer it. Dont forget that as valves ” need ” adjusting, more than likely they need to be loosened up.

I’ll take it apart and do that. Code pour ajouter ce livre sur votre site: Feel like burning it. Posted by ddstrydom on Apr 13, IMMduly completed. Not finding what you are looking for? Hev Level 3 Expert Answers.

Need help valve question. – Yamaha R1 Forum: YZF-R1 Forums

Document Checklist – For a Study Permit. Causes can be many one is because it’s a carburetor type engine it is sensitive to atmospheric changes as in altitude, temperature and humidity. The email address entered is already associated to an account.


Login to post Please use English characters only. Do not drill the needle hole. I would remove and clean all the plugs, check the gaps and re-install so you can check again later if needs be. Canada Express Study Program checklist Air fuel mixture adjustment too lean. I have to rev the hell out of her and ride the clutch to get going or just wait until she kicks in. City of Laconia Department of Code Helpful 1 Not Helpful 17 Comments Flag. Nov 10, Yamaha Dnyojet Go to this site, download the installation instructions, and read the part about adjusting the accelerator pump.

Originally posted by biaggi If he’s done a major service then setting up the carbs should be included Your plug does look rich or an electrical problem. Question about Yamaha YZF-R1 Motorcycles 1 Answer Can i adjust the carbs on my yamaha r1 to run a bit richer what dyynojet i do cause my bike is running lean over rpm.