ALIGN 3GX 2.1 MANUAL PDFALIGN 3GX 2.1 MANUAL PDF

The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. Align 3Gx flybarless setup problem Electric Heli Talk. Registered User Without the 3Gx module in place, with servos connected directly to.

Author: Shaktitaur Kajimuro
Country: Syria
Language: English (Spanish)
Genre: Software
Published (Last): 12 March 2016
Pages: 35
PDF File Size: 4.46 Mb
ePub File Size: 18.14 Mb
ISBN: 235-4-77856-851-7
Downloads: 28503
Price: Free* [*Free Regsitration Required]
Uploader: Nirisar

Well done eban I didn’t spot the mistake and the problem nearly brought manjal very short experiment with FBL to an untimely end. I know I might have figured that was wrong earlier, but I’m new to fbl and was concentrating on getting the colours exactly in the order shown in the manual.

Align 3gx pdf manual

Password Please enter a password for your user account. And yes you remove the bind plug while still powered, it sets fail safes, throttle etc. Microbeast or 3GX for Flybarless setup. I have 2 sats, so would I just: That’s a bit awkward for, if I read the CD correctly, I have to do that with the 3Gx installed in the heli, which means bringing the whole thing to my PC because I don’t have a laptop like they show in the CD.

Align 3GX v setup – RC

Adjust the maximum collective pitch using the transmitter’s swashplate mixing function pitch swash AFR. Feb 05, That’s kinda what I figured thanks! Plug in flight battery 3.

If you use the software there are text and pop-ups to aljgn the settings: This completes the swashplate mixing type recognization process.

  JC RYLE DUTIES OF PARENTS PDF

Feb 04, He was getting a bit defensive, suggesting I had some kind of mix in my transmitter, but I kept reminding him kanual behaved normally when connected direct to my receiver.

Reset throttle curve and pitch curve to default Gyro gain For radio with built in gyro gain settings, gain can be adjusted directly. With all channels stationary, move the transmitter aileron stick to the right and then back to center position.

Press and hold the SET button while powering up the receiver.

User need to confirm if 3GX is mounted right side up or upside down. Please double check this. While keeping swashplate level and main pitch at zero degrees, press the SET button to register the neutral point and enter E. Should there be changes such as 3GX software update, pitch reconfiguration, or subtrim adjustments, the setup process must be repeated for the flybarless system.

Wait for some sort of jingle or series of flashing lights then release bind button Does that sound right? Subsequent setup mode is entered by a single press of the SET button. Suitable for helicopter of all class from toglow engine or electric powered.

Power on Futaba 10C 5. Align 3GX version 2. Insert bind plug into 3gx 2. If needed, servo reverse is done from the transmitter’s REV reverse function.

Confirm the transmitter is powered up, and throttle stick is at lowest position.

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic. Custom parameters have been opened up in 3GX to allow pilots to fine tune numerous settings for swashplate and rudder.

  IMAGINING RELIGION FROM BABYLON TO JONESTOWN PDF

It just the way Align assigned channels in the 3GX unit versus the way Futaba assigned channels in its rx and S-bus. With the APS gyro, the helicopter will have the ability to self stabilize, hold position as well as altitude, and even autonomous way point flights as well as return home.

Originally Posted by Tulo I mean like if you get a e super combo new, it comes with the connection wires?

Aileron and elevator rates can be adjusted in 3GX panel or cyclic pitch rate adjustment under flight mode settings.

I also noticed that adjusting the sub-trim for channel 6 in my transmitter didn’t have any effect on the servo; doing the same for channel 1 I could see and feel channel 1 servo arm moving slightly. Why does that manual start on page 20?

3GX manual – HeliFreak

Actual gain value differs amongst servos and helicopters. I spoke to the UK distributor today about my problem, and after a while we agreed that it seemed like the channel 6 servo was behaving as if it had a curve programmed to it.

Are there pages missing?

The trim must be zero when using 3GX, and should not be adjusted at anytime. Feb 07, We are reading from the same manual.

At first I thought I had a bad servo, but when I reconnected everything directly to the receiver it worked fine, so I’m thinking it must be the 3Gx unit. Eventually there will also be smartphone apps allowing live adjustments to 3GX without powering down.